keywords: ip pbx voip gateway gsm gateway

×

Notice

The forum is in read only mode.
  1. Forum
  3. Telephony Cards Support
  5. GSM/WCDMA Series
  7. GSM span X: Provisioned, Down, Active
× Questions about G400/G410 Cards.

GSM span X: Provisioned, Down, Active

13 years 6 months ago #6319 by ricardo
Hi!

I used chan-extra and I think everything is configured, but when I type "gsm show spans" on asterisk cli i get:
GSM span 1: Provisioned, Down, Active
GSM span 2: Provisioned, Down, Active
and gsm show span 1 says:
D-channel: 2
Status: Provisioned, Down, Active
Switchtype: SimCom 100/300
Type: CPE
Network Status: Unregistered
Network Name:
Net Coverage (0,31): -1
SIM IMSI:
Card IMEI:

Does "Net Coverage" mean that I don't have any signal there and so the Stauts is "down"?
Or is there another problem ?

Thank you
13 years 6 months ago #6320 by svolta
Hi,
Please stop your asterisk and dahdi, then run command "modprobe opvxg4xx debug=9" then "asterisk -vvvgc", "dmesg", and send me the message of "dmesg"!
13 years 6 months ago #6321 by ricardo
Hi!

dmesg:
[61413.971468] opvxg4xx 0000:01:0a.0: enabling device (0000 -> 0002)
[61413.971468] ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
[61413.971468] bus number = 1 devfn = 80 irq = 17
[61413.971468] pci-io-phys = fdfe0000
[61413.971468] opvxg4xx: iomem at fdfe0000 size 65536
[61413.971468] opvxg4xx: iomem remote to ffffc20000660000
[61413.971468] Found an OpenVox G400P: Version 1.0
[61413.971468] opvxg4xx: slot 0 is Installed
[61413.971468] opvxg4xx: slot 1 is Installed
[61413.971468] opvxg4xx: slot 2 is Empty
[61413.971468] opvxg4xx: slot 3 is Empty
[61413.971468] err = 0
[61413.971468] opvxg4xx: Powering up all spans...
[61422.570409] pci_io addr is 0xffffc20000660000
[61551.895712] opvxg4xx: HDLC span 0 TX [ ATZ\r\n ] 5
[61551.895712] opvxg4xx: HDLC span 1 TX [ ATZ\r\n ] 5
[...]
[62940.749726] opvxg4xx: HDLC span 0 TX [ ATZ\r\n ] 5
[62940.749726] opvxg4xx: HDLC span 1 TX [ ATZ\r\n ] 5
[62999.332882] opvxg4xx: HDLC span 0 TX [ ATZ\r\n ] 5
[62999.332882] opvxg4xx: HDLC span 1 TX [ ATZ\r\n ] 5
[63059.350403] opvxg4xx: HDLC span 0 TX [ TZ\r\nATZ\r\n ] 9
[63059.350403] opvxg4xx: HDLC span 1 TX [ TZ\r\nATZ\r\n ] 9
[63527.503102] opvxg4xx: HDLC span 0 TX [ TZ\r\nATZ\r\nATZ\r\n ] 14
[63527.503125] opvxg4xx: HDLC span 1 TX [ TZ\r\nATZ\r\nATZ\r\n ] 14
[64624.952626] opvxg4xx: HDLC span 0 TX [ TZ\r\nATZ\r\nATZ\r\nATZ\r\n ] 19
[64624.952692] opvxg4xx: HDLC span 1 TX [ TZ\r\nATZ\r\nATZ\r\nATZ\r\n ] 19
asterisk starts normally and with the spans nothing changed
gsm show span 1
D-channel: 2
Status: Provisioned, Down, Active
Switchtype: SimCom 100/300
Type: CPE
Network Status: Unregistered
Network Name:
Net Coverage (0,31): -1
SIM IMSI:
Card IMEI:
And what is switchtype = simcom?

We have the pin disabled, but is there a way to enter the pin? In some example files (e.g. zapata.conf.duoGSM) there was something like:
; phone number for SIM card in slot A
;exten=016012345671
; PIN for SIM card in slot A
;pin=1234
and switchtypes:
;switchtype=em200
switchtype=sim340dz
;switchtype=m20
;switchtype=g20
but with dahdi we use simcom!?!

And when I reload the module chan_extra.so I have another strange thing:
module reload chan_extra.so
    -- Reloading module 'chan_extra.so' (EXTRA Telephony)
  == Parsing '/etc/asterisk/chan_extra.conf':   == Found
  == Parsing '/etc/asterisk/extra-channels.conf':   == Found
  == Parsing '/etc/asterisk/users.conf':   == Found
[Oct 22 10:16:58] WARNING[3542]: chan_extra.c:17016 process_extra: Ignoring any changes to 'switchtype' (on reload) at line 11.
[Oct 22 10:16:58] WARNING[3542]: chan_extra.c:17016 process_extra: Ignoring any changes to 'signalling' (on reload) at line 12.
    -- Reconfigured channel 1, GSM signalling
[Oct 22 10:16:58] DEBUG[3542]: chan_extra.c:16199 process_extra: Channel '1' configured.
[Oct 22 10:16:58] WARNING[3542]: chan_extra.c:17016 process_extra: Ignoring any changes to 'switchtype' (on reload) at line 21.
[Oct 22 10:16:58] WARNING[3542]: chan_extra.c:17016 process_extra: Ignoring any changes to 'signalling' (on reload) at line 22.
    -- Reconfigured channel 3, GSM signalling
[Oct 22 10:16:58] DEBUG[3542]: chan_extra.c:16199 process_extra: Channel '3' configured.

i] Last edited by ricardo at 2010-10-22 16:16 [/i
13 years 6 months ago #6331 by svolta
Hi,
Can you send your shh to me by Email, my Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Also you can add my MSN: This email address is being protected from spambots. You need JavaScript enabled to view it.
13 years 6 months ago #6332 by ricardo
We had a problem with the PCI-Slot. After changing the slot everything is fine :)

Thanks to svolta!!!
  1. Forum
  3. Telephony Cards Support
  5. GSM/WCDMA Series
  7. GSM span X: Provisioned, Down, Active
Time to create page: 0.038 seconds
Powered by Kunena Forum