×
Notice
The forum is in read only mode.
Forum
Asterisk Zaptel OS
A810P problem detecting module
×
Technical information on install and config asterisk, zaptel under different OSs
A810P problem detecting module
11 years 2 months ago #8606
by mike.salazar
Hi,
I Have installed dahdi-linux-complete-2.6.1+2.6.1 in centos 6.3 32bit and when i run dahdi_genconf iget this message
Default parameters from /etc/dahdi/genconf_parameters
Empty configuration -- no spans
Generating /etc/dahdi/system.conf
Empty configuration -- no spans
Generating /etc/asterisk/dahdi-channels.conf
also i'm getting this message in dmesg
12.200702] dahdi: Telephony Interface Registered on major 196
[ 12.200707] dahdi: Version: 2.6.1
[ 12.244757] alloc irq_desc for 101 on node -1
[ 12.244764] alloc kstat_irqs on node -1
[ 12.244778] opvxa24xx 0000:0a:03.0: PCI INT A -> GSI 101 (level, low) -> IRQ 101
[ 13.745009] OpenVox A810P version: 1.4
[ 15.245148] Module 0: Not installed
[ 15.245151] Module 1: Not installed
[ 15.245154] Module 2: Not installed
[ 15.245156] Module 3: Not installed
[ 15.245158] Module 4: Not installed
[ 15.245160] Module 5: Not installed
[ 15.245162] Module 6: Not installed
[ 15.245165] Module 7: Not installed
[ 15.245260] dahdi: disable_span: span 1
[ 15.246916] opvxa24xx: probe of 0000:0a:03.0 failed with error -5
Please assist.
Thanks
Less
More
Posts: 26
Karma: 2
Thank you received: 3
11 years 2 months ago #8607
by tim.june
Did you check the power supply for A810P? it needs external power source.And make sure opvxa24xx has been loaded.
Send me remote access if you need me to check it for you.
This email address is being protected from spambots. You need JavaScript enabled to view it.
i] Last edited by tim.june at 2013-2-22 16:41 [/i
Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Skype: tim.jjune
11 years 2 months ago #8608
by mike.salazar
Hi,
I only have FXO card. The power supply only need for FXS right? Also it does not come with power supply cord only a timing cable.
Less
More
Posts: 26
Karma: 2
Thank you received: 3
11 years 2 months ago #8609
by tim.june
No matter FXO or FXS, power supply is necessary!
A810P provides a 4 pin power jack, you need to get power source from the host power supply.
Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Skype: tim.jjune
11 years 2 months ago #8610
by mike.salazar
I see, I'll try that first. I also have a1200P working perfectly without power supply that's why i thought power supply is not necessary for FXO modules.
Thanks for the info, i'll let you know.
Less
More
Posts: 26
Karma: 2
Thank you received: 3
11 years 2 months ago #8611
by tim.june
I know, A1200P with FXO modules can work without power supply. But A810P use different design layout, need power anyway.
Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Skype: tim.jjune
Forum
Asterisk Zaptel OS
A810P problem detecting module
Time to create page: 0.040 seconds