Caller ID not working!!

Hello,

i have an OpenVox A400E working on a system with TrixBox 2.8 and the caller id is not working.

I need help with this, i have tried many configurations but no success.

The system has a IVR to answer the calls.

Thanks in advance,
Felipe

Follow some configurations files:

chand_dahdi.conf

[trunkgroups]

[channels]
language=br
context=from-pstn
signalling=fxs_ks
rxwink=300 ; Atlas seems to use long (250ms) winks
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=no
;echotraining=800
faxdetect=incoming
rxgain=6.0
txgain=5.0
callgroup=1
pickupgroup=1
cidstart=polarity
cidsignalling=dtmf
relaxdtmf=yes
callerid=asreceived

;Uncomment these lines if you have problems with the disconection of your analog lines
busydetect=yes
busycount=5


immediate=no

#include dahdi_additional.conf
#include dahdi-channels.conf

dahdi-channels.conf

; Autogenerated by /usr/sbin/dahdi_genconf on Mon Aug 22 16:56:49 2011
; If you edit this file and execute /usr/sbin/dahdi_genconf again,
; your manual changes will be LOST.
; Dahdi Channels Configurations (chan_dahdi.conf)
;
; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended
; to be #include-d by /etc/chan_dahdi.conf that will include the global settings
;

; Span 1: WCTDM/4 "Wildcard TDM400P REV E/F Board 5" (MASTER)
;;; line="1 WCTDM/4/0 FXSKS (In use) (SWEC: MG2)"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 1
callerid=
group=
context=default

;;; line="2 WCTDM/4/1 FXSKS (In use) (SWEC: MG2)"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 2
callerid=
group=
context=default

;;; line="3 WCTDM/4/2 FXSKS (In use) (SWEC: MG2)"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 3
callerid=
group=
context=default

indications.conf

[general]
country=br

system.conf

# Span 1: WCTDM/4 "Wildcard TDM400P REV E/F Board 5" (MASTER)
fxsks=1
echocanceller=mg2,1
fxsks=2
echocanceller=mg2,2
fxsks=3
echocanceller=mg2,3
# channel 4, WCTDM/4/3, no module.

# Global data

loadzone = br
defaultzone = br

i] Last edited by felipeasf at 2011-8-23 04:14 [/i

hi,
you will confirm the type of caller ID signalling in use ,fsk or dtmf. you can change cidstart=ring to try,
if still have problem,please send me a record with CID signailing or give me ssh, I will check it for you.

My Email:This email address is being protected from spambots. You need JavaScript enabled to view it.

Please execute the following command to record line signal under command line:
# dahdi_monitor 1 -r r.pcm -t t.pcm
('1' means the channel number where your FXO setup.)
Please send r.pcm and t.pcm files and provide the phone number and SSH to This email address is being protected from spambots. You need JavaScript enabled to view it.




i] Last edited by tim.june at 2011-8-23 11:00 [/i

E-mail sent!

Thanks.