zttool show YEL at Alarm

Hi all, I see YEL at Alarm in zttool after I install the D110P card to connect Nortel M1 PBX by ISDN. Any idea to correct this issue?

My zaptel.conf
span=1,1,0,ccs,hdb3,crc4
bchan=1-15
dchan=16
bchan=17-31
loadzone = us
defaultzone=us

hello
1 please show us more configuration information.
2 is the line ISDN pri line? please check your line and line connection.
3 please unplug the line, and check what is the card LED status.

Hi Robert, thanks for your prompt reply.
1 please show us more configuration information.
=> What kind of configuration you need to know? I am using zaptel 1.4.12.1 but libpri 1.2.8.
zapata.conf ==================
[channels]
context=zap-in
switchtype=euroisdn
pridialplan=national
signalling=pri_net
usecallerid=yes
hidecallerid=no
callwaiting=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
echocancel=yes
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
callprogress=no
callerid=asreceived
group=1
channel => 1-15,17-31
===============================
dmesg==========================
[ 34.949416] Zapata Telephony Interface Registered on major 196
[ 34.949423] Zaptel Version: 1.4.12.1
[ 34.949425] Zaptel Echo Canceller: MG2
[ 35.010573] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ
21
[ 35.011553] FALC version: 00000000
[ 35.011558] TE110P: Setting up global serial parameters for E1 FALC V1.2
[ 35.011605] TE110P: Successfully initialized serial bus for card
[ 35.012343] Found a Wildcard: Digium Wildcard TE110P T1/E1
[ 36.820358] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ
22
[ 37.139118] NET: Registered protocol family 10
[ 37.139588] lo: Disabled Privacy Extensions
[ 37.159109] intel8x0_measure_ac97_clock: measured 51496 usecs
[ 37.159117] intel8x0: clocking to 48000
[ 38.529803] eth0: Media Link On 100mbps full-duplex
[ 40.196220] loop: module loaded
[ 40.237410] lp0: using parport0 (interrupt-driven).
[ 40.684477] Adding 9759476k swap on /dev/sda1. Priority:-1 extents:1 across:
9759476k
[ 41.117200] EXT3 FS on sda2, internal journal
[ 42.464625] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 44.723521] Registered tone zone 0 (United States / North America)
[ 44.723620] TE110P: Span configured for CCS/HDB3/CRC4
[ 44.723625] Calling startup (flags is 4099)
[ 47.358259] eth0: no IPv6 routers present
[ 50.747645] TE110P: Span configured for CCS/HDB3/CRC4
[ 50.747664] Calling startup (flags is 4099)
===============================
cat /proc/zaptel/*==================
Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" (MASTER) HDB3/CCS/CRC4 YELLOW

1 WCT1/0/1 Clear (In use) YELLOW
2 WCT1/0/2 Clear (In use) YELLOW
3 WCT1/0/3 Clear (In use) YELLOW
4 WCT1/0/4 Clear (In use) YELLOW
5 WCT1/0/5 Clear (In use) YELLOW
6 WCT1/0/6 Clear (In use) YELLOW
7 WCT1/0/7 Clear (In use) YELLOW
8 WCT1/0/8 Clear (In use) YELLOW
9 WCT1/0/9 Clear (In use) YELLOW
10 WCT1/0/10 Clear (In use) YELLOW
11 WCT1/0/11 Clear (In use) YELLOW
12 WCT1/0/12 Clear (In use) YELLOW
13 WCT1/0/13 Clear (In use) YELLOW
14 WCT1/0/14 Clear (In use) YELLOW
15 WCT1/0/15 Clear (In use) YELLOW
16 WCT1/0/16 HDLCFCS (In use) YELLOW
17 WCT1/0/17 Clear (In use) YELLOW
18 WCT1/0/18 Clear (In use) YELLOW
19 WCT1/0/19 Clear (In use) YELLOW
20 WCT1/0/20 Clear (In use) YELLOW
21 WCT1/0/21 Clear (In use) YELLOW
22 WCT1/0/22 Clear (In use) YELLOW
23 WCT1/0/23 Clear (In use) YELLOW
24 WCT1/0/24 Clear (In use) YELLOW
25 WCT1/0/25 Clear (In use) YELOW
26 WCT1/0/26 Clear (In use) YELLOW
27 WCT1/0/27 Clear (In use) YELLOW
28 WCT1/0/28 Clear (In use) YELLOW
29 WCT1/0/29 Clear (In use) YELLOW
30 WCT1/0/30 Clear (In use) YELLOW
31 WCT1/0/31 Clear (In use) YELLOW
=======================================
2 is the line ISDN pri line? please check your line and line connection.
=> Yes, it is. The line & connection is ok.
3 please unplug the line, and check what is the card LED status.
=> LED is keeping on RED when the line is connected. LED is turing on RED but in twinkling

hi
1 Which country are you in? Please try to disable the crc4 parameter in zaptel.conf
2 If it still can not work, please email your ssh to me: This email address is being protected from spambots. You need JavaScript enabled to view it.