FXS instead FXO dahdi_genconf A800p

Hi!i´ve been trying to install my A800p with no results at all. I´m using FreePbx 2.10.4 ( CentOS 6,4).
Fisrtly i did all the steps in the A800p documentation http://downloads.openvox.cn/pub/ ... HDI_User_Manual.pdf . i yum installed all the required modules and tried to run dahdi_genconf and get this:

[root@unknown-00-25-22-3e-29-4basterisk]# dahdi_genconf
Empty configuration -- no spans
Empty configuration -- no spans

Thanks to this post http://bbs.openvox.cn/viewthread.php?tid=1708 , by removind and blaklisting the module "hisax", i was able to run dahdi_genfconf and get some result in the /etc/dahdi/system.conf file, but it wasn´t what i expected. This is the result:

[root@unknown-00-25-22-3e-29-4b ~]# cat /etc/dahdi/system.conf
# Autogenerated by /usr/sbin/dahdi_genconf on Tue Jan 8 19:01:18 2013
# If you edit this file and execute /usr/sbin/dahdi_genconf again,
# your manual changes will be LOST.
# Dahdi Configuration File
#
# This file is parsed by the Dahdi Configurator, dahdi_cfg
#
# Span 1: OPVXA1200/12 "OpenVox A1200P/A800P Board 13" (MASTER)
fxsks=1
echocanceller=oslec,1
fxsks=2
echocanceller=oslec,2
fxsks=3
echocanceller=oslec,3
fxsks=4
echocanceller=oslec,4
fxsks=5
echocanceller=oslec,5
# channel 6, OPVXA1200/12/5, no module.
# channel 7, OPVXA1200/12/6, no module.
# channel 8, OPVXA1200/12/7, no module.

# Global data

loadzone = us
defaultzone = us


And this is the dahdi-channels.conf

[root@unknown-00-25-22-3e-29-4b ~]# cat /etc/asterisk/dahdi-channels.conf
; Autogenerated by /usr/sbin/dahdi_genconf on Tue Jan 8 19:01:18 2013
; If you edit this file and execute /usr/sbin/dahdi_genconf again,
; your manual changes will be LOST.
; Dahdi Channels Configurations (chan_dahdi.conf)
;
; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended
; to be #include-d by /etc/chan_dahdi.conf that will include the global settings
;

; Span 1: OPVXA1200/12 "OpenVox A1200P/A800P Board 13" (MASTER)
;;; line="1 OPVXA1200/12/0 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 1
callerid=
group=
context=default

;;; line="2 OPVXA1200/12/1 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 2
callerid=
group=
context=default

;;; line="3 OPVXA1200/12/2 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 3
callerid=
group=
context=default

;;; line="4 OPVXA1200/12/3 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 4
callerid=
group=
context=default

;;; line="5 OPVXA1200/12/4 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-pstn
channel => 5
callerid=
group=
context=default

Which is very unexpected because i need the card's FXO. in fact, if a run dahdi_scan


[root@unknown-00-25-22-3e-29-4b ~]# dahdi_scan
[1]
active=yes
alarms=OK
description=OpenVox A1200P/A800P Board 13
name=OPVXA1200/12
manufacturer=OpenVox
devicetype=OpenVox A1200P/A800P
location=PCI Bus 01 Slot 09
basechan=1
totchans=8
irq=0
type=analog
port=1,FXO
port=2,FXO
port=3,FXO
port=4,FXO
port=5,FXO
port=6,none
port=7,none
port=8,none
If i write the system.conf file manually, once i try # dahdi_cfg –vvvvvv for relaoding the parameters, i recieve this message:
Channel 01: FXO Loopstart (Default) (Echo Canceler: oslec) (Slaves: 01)
Channel 02: FXO Loopstart (Default) (Echo Canceler: oslec) (Slaves: 02)
Channel 03: FXO Loopstart (Default) (Echo Canceler: oslec) (Slaves: 03)
Channel 04: FXO Loopstart (Default) (Echo Canceler: oslec) (Slaves: 04)
Channel 05: FXO Loopstart (Default) (Echo Canceler: oslec) (Slaves: 05)
5 channels to configure.Changing signalling on channel 1 from FXS Kewlstart to FXO Loopstart DAHDI_CHANCONFIG failed on channel 1: Invalid argument (22)Selected signaling not supportedPossible causes:
FXO signaling is being used on a FXO interface (use a FXS signaling variant)
RBS signaling is being used on a E1 CCS span
Signaling is being assigned to channel 16 of an E1 CAS span

i deeply appreciate for advance any help, idea or reference

Hi Alan,
I noticed that you have 5 FXO modules on A800P, and FXO module uses fxsks/fxsls signalling, not fxoks/fxols, when you edit the system.conf, you should know that.
when you did command 'dahdi_genconf', it will create system.conf, and the configuration is all right, you have no need to modify it.