- Posts: 4
- Thank you received: 0
×
Questions about VS-GW2120/GW1600/GW1202 and WGW1002G GSM Series VoIP Gateway
Recovery adfter Firmware upgrade
5 years 11 months ago #11609
by hexus
Hi.
I have an VS-GGU-E2M0400 with 2 cards (8 GSM total)
It was with 2.3.2 firmware onboard and after check i find out that already 2.3.8 released
Via web interface i tied Online Update. But after reboot status shows that only MASTER card updated, slave still 2.3.2. So i've downloaded firmware from downloads.openvox.cn/pub/firmwares/GSM%2...ay/wg400-current.bin (link taken from datail window of Online update). And try to update slave card manually via uploading firmware file. After reboot my slave card have status DISCONECTED.
So can i rollback to factory firmware ??? Reset button seems do nothing.
I have an VS-GGU-E2M0400 with 2 cards (8 GSM total)
It was with 2.3.2 firmware onboard and after check i find out that already 2.3.8 released
Via web interface i tied Online Update. But after reboot status shows that only MASTER card updated, slave still 2.3.2. So i've downloaded firmware from downloads.openvox.cn/pub/firmwares/GSM%2...ay/wg400-current.bin (link taken from datail window of Online update). And try to update slave card manually via uploading firmware file. After reboot my slave card have status DISCONECTED.
So can i rollback to factory firmware ??? Reset button seems do nothing.
5 years 11 months ago #11611
by heizi.lv
Hi,
Sorry for the trouble. Please make sure if the SYS led of slave board flashes or not.
If the SYS led is off, i think the file system of slave board is broken. We need an USB-TTL cable to bring it up. Please prepare an USB-TTL cable and follow the manual to flash system firmware:
www.openvox.cn/pub/misc/tools/Flash%20Vo...0USB-TTL%20cable.pdf
If you need any help, you can add my skype for contact. My skype: This email address is being protected from spambots. You need JavaScript enabled to view it.
Sorry for the trouble. Please make sure if the SYS led of slave board flashes or not.
If the SYS led is off, i think the file system of slave board is broken. We need an USB-TTL cable to bring it up. Please prepare an USB-TTL cable and follow the manual to flash system firmware:
www.openvox.cn/pub/misc/tools/Flash%20Vo...0USB-TTL%20cable.pdf
If you need any help, you can add my skype for contact. My skype: This email address is being protected from spambots. You need JavaScript enabled to view it.
5 years 11 months ago - 5 years 11 months ago #11612
by hexus
SYS led is off
It can blink for 1-2 seconds when i hold reset button and powering on, but after release remain off
Where can i get such cable, or maybe flash devise via tftp without cable ? like any other router using openwrt image ??
It can blink for 1-2 seconds when i hold reset button and powering on, but after release remain off
Where can i get such cable, or maybe flash devise via tftp without cable ? like any other router using openwrt image ??
Last Edit: 5 years 11 months ago by hexus.
5 years 10 months ago - 5 years 10 months ago #11616
by hexus
And another question
1.I found version of *.IMG firmware, other images are *.BIN. Can i use Bin images for flashing my device ?
2. In attached instruction
Notice:
Check “rootmtdblock=/dev/mtdblockX” filed, if it shows “mtdblock6”, then execute “update
second” to flash firmware; if “mtdblock4”, then execute “update first”.
BUT my print says something like
rootmtdblock=/dev/ubiblk0_0
What command should i use for update ?
Thanks .
1.I found version of *.IMG firmware, other images are *.BIN. Can i use Bin images for flashing my device ?
2. In attached instruction
Notice:
Check “rootmtdblock=/dev/mtdblockX” filed, if it shows “mtdblock6”, then execute “update
second” to flash firmware; if “mtdblock4”, then execute “update first”.
BUT my print says something like
rootmtdblock=/dev/ubiblk0_0
What command should i use for update ?
Thanks .
Last Edit: 5 years 10 months ago by hexus.
5 years 10 months ago #11617
by heizi.lv
Hi,
Sorry for the trouble.
1) You can only flash .img firmware.
2) Here are the commands you need if rootmtdblock=/dev/ubiblk0_0 :
setenv ipaddr XXXXX
setenv serverip XXXXX
setenv fsfile wg400-current.img
setenv rootmtdblock /dev/mtdblock4
run updatefirst
mtdparts
nand erase offset size
nand erase 0x00100000 0x00080000
nand erase 0x00180000 0x00080000
reset
Sorry for the trouble.
1) You can only flash .img firmware.
2) Here are the commands you need if rootmtdblock=/dev/ubiblk0_0 :
setenv ipaddr XXXXX
setenv serverip XXXXX
setenv fsfile wg400-current.img
setenv rootmtdblock /dev/mtdblock4
run updatefirst
mtdparts
nand erase offset size
nand erase 0x00100000 0x00080000
nand erase 0x00180000 0x00080000
reset
Time to create page: 0.051 seconds