B100M & mISDN + Voyage on ALIX

Hope anybody can help me with B100M and mISDN integration. at the moment im stuck with the following setup:
-
OS: Voyage 2.6.23-486
HW: Alix 2c2 with OpenVox B100M
Asterisk: asterisk-1.4.22 (not yet relevant)
-


after installing the following packages:
- libpri-1.4.8,
- mISDN-1_1_8,
- mISDNuser-1_1_8,

I wanted to configure and start mISDN.


# mISDN scan
1 mISDN compatible device(s) found:
>> hfcpci

# mISDN config
Writing /etc/mISDN.conf for 1 mISDN compatible device(s):
>> hfcpci

# mISDN start
-- Loading mISDN modules --
>> /sbin/modprobe --ignore-install capi
>> /sbin/modprobe --ignore-install mISDN_core debug=0
>> /sbin/modprobe --ignore-install mISDN_l1 debug=0
>> /sbin/modprobe --ignore-install mISDN_l2 debug=0
>> /sbin/modprobe --ignore-install l3udss1 debug=0
>> /sbin/modprobe --ignore-install mISDN_capi
>> /sbin/modprobe --ignore-install hfcpci protocol=0x2 layermask=0xf



after that, my box does a reboot without further notice or log events :-/

messages while booting:
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4



a little debug output
# lspci -vvvvvvvvvv
00:0e.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02)
Subsystem: Cologne Chip Designs GmbH ISDN Board
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 (4000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1800
Region 1: Memory at e0080000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-


thanks for help.

hello:
please remove some modules like isdn and Hisax, add those two packages in blicklist.
regards!
James.zhu

thanks.

in /etc/modprobe.d/blacklist, I added:
blacklist hisax
blacklist hisax_fcpcipnp
blacklist hisax_isac
blacklist crc_ccitt
blacklist isdn
blacklist slhc
blacklist capi
blacklist kernelcapi
blacklist kernel_capi
blacklist avmfritz
blacklist capif

no success though
not working either, same as "mISDN start" (but not surprising):


# /usr/sbin/misdn-init start

---

Loading module(s) for your misdn-cards:

---

/sbin/modprobe --ignore-install hfcpci protocol=0x2 layermask=0xf
<reboot>



# lsmod
Module Size Used by
dahdi_dummy 3404 0
xpp_usb 14664 0
xpp 132744 1 xpp_usb
wctc4xxp 40472 0
dahdi_transcode 6408 1 wctc4xxp
wcb4xxp 86436 0
wctdm 33868 0
wcfxo 10272 0
wctdm24xxp 105600 0
wcte11xp 22944 0
wct1xxp 12064 0
wcte12xp 61792 0
wct4xxp 303232 0
firmware_class 6912 4 wctc4xxp,wctdm24xxp,wcte12xp,wct4xxp
dahdi 182920 13 dahdi_dummy,xpp,dahdi_transcode,wcb4xxp,wctdm,wcfxo,wctdm24xxp,wcte11xp,wct1xxp,wcte12xp,wct4xxp
crc_ccitt 2048 1 dahdi
ipv6 208132 12
dm_mod 40640 0
ledtrig_timer 2944 0
ledtrig_heartbeat 2176 0
leds_alix 2564 0
led_class 3460 1 leds_alix
geodewdt 3596 2
scx200_acb 4740 0
hwmon_vid 2432 0
lm90 11944 0
i2c_core 18192 2 scx200_acb,lm90
hostap_pci 44688 0
hostap 94596 1 hostap_pci
ieee80211_crypt 4480 1 hostap
natsemi 22624 0
cs5535_gpio 3828 0
ohci_hcd 15620 0
ehci_hcd 23820 0
usbcore 100760 4 xpp_usb,ohci_hcd,ehci_hcd
via_rhine 18312 0
mii 4352 1 via_rhine
bitrev 1792 2 natsemi,via_rhine
crc32 3840 2 natsemi,via_rhine

hello:
please email your ssh to: This email address is being protected from spambots. You need JavaScript enabled to view it.
regards!
James.zhu

i was told that the b100m is not stable to run on alix2c2. thus i will upgrade to b200m in the next few days, lets see how this goes.