keywords: ip pbx voip gateway gsm gateway

  1. Forum
  3. Telephony Cards Support
  5. B100/200/400/800 Series
  7. Many entry Got FIFO TX ...
× Questions about B100/200/400/800 ISDN BRI Cards

Many entry Got FIFO TX ...

9 years 4 months ago #9185 by hua
HI

It is just a warning, Can you how me the output of "cat /proc/interrupts".

upper
9 years 4 months ago #9186 by pdifeo 
CPU0       CPU1       CPU2       CPU3 
  0:   54540856          0          0          0    IO-APIC-edge  timer
  8:          1          0          0          0    IO-APIC-edge  rtc
  9:          0          0          0          0   IO-APIC-level  acpi
 58:     548977          0          0          0         PCI-MSI  ahci
 66:    1788697          0          0          0         PCI-MSI  eth0
169:   54499374          0          0          0   IO-APIC-level  b4xxp
177:   54388712          0          0          0   IO-APIC-level  opvxd115
225:         26          0          0          0   IO-APIC-level  ehci_hcd:usb1
233:         26          0          0          0   IO-APIC-level  ehci_hcd:usb2
NMI:      17927        888        907        960 
LOC:   54538704   54538795   54538698   54538620 
ERR:          0
MIS:          0



Reagards
Pasquale
9 years 4 months ago #9204 by pdifeo
Hi,

please tell me if all is ok.

I'm very frustrated. The card is setted in NT mode. On other side there is a faxserver with an AVM ISDN Controller C2.
If I send a fax all works fine. When receiving don't work. In the system there is also an DE130E card. Is possible that the problem is on timing between cards?

Thanks in advance.
Pasquale
9 years 4 months ago #9205 by hua
HI,

I have checked all the configures that you posted here ,the settings all ok, If possible please remove DE130E and just test B400 card . By the way I have accept you invite on skype .

Best regards
upper
9 years 4 months ago #9208 by pdifeo
Hi, but If I remove DE130E card I don't have how to make a test.

I have also set the channel to use 3K1AUDIO transfer capability when the system receive faxes. The stranger thing is that when send a fax there aren't problems. So, I think, that the problem is not on timing.

The cards are both PCI-e.

I will inform you that the command lspci -vb show that the two cards work togheter on IRQ 11. It's normal ?
02:00.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)
        Subsystem: Cologne Chip Designs GmbH HFC-4S [OpenVox B200P / B400P]
        Flags: medium devsel, IRQ 11
        I/O ports at 2000
        Memory at c1300000 (32-bit, non-prefetchable)
        Capabilities: [40] Power Management version 2
        Kernel driver in use: wcb4xxp
        Kernel modules: wcb4xxp
06:00.0 Network controller: OpenVox Communication Co. Ltd. D130P/D130E Single-port E1/T1 card (3rd GEN) (rev 15)
        Subsystem: Device 0005:0000
        Flags: bus master, slow devsel, latency 64, IRQ 11
        Memory at c1100000 (32-bit, non-prefetchable)
        Kernel driver in use: opvxd115
        Kernel modules: opvxd115
9 years 4 months ago #9209 by miaolin
what is the "not work"? the call was established before fax receive ? if no , it should be a signaling issue, otherwise, could you post error here?
  1. Forum
  3. Telephony Cards Support
  5. B100/200/400/800 Series
  7. Many entry Got FIFO TX ...
Time to create page: 0.038 seconds
Powered by Kunena Forum