keywords: ip pbx voip gateway gsm gateway

× Questions about B100/200/400/800 ISDN BRI Cards

B100P - "Empty configuration -- no spans"

11 years 5 months ago #7436 by tim.june
Firstly, when load the driver, please try to use " modprobe zaphfc " instead of "modprobe vzaphfc".
If not work, you can try the new patch below, the way to patch is shown in the file.

Still any problems, please send SSH to my Email: This email address is being protected from spambots. You need JavaScript enabled to view it., I will check for you.
BTW, this driver has included all modules for OpenVox card, including B100P/E/M:
http://downloads.openvox.cn/pub/drivers/dahdi-linux-complete/releases/1.3.3/openvox_dahdi-linux-complete-2.5.0.1+2.5.0.1.tar.gz

i] Last edited by tim.june at 2012-2-10 15:21 [/i

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Skype: tim.jjune
Attachments:
11 years 5 months ago #7437 by webon
No way. I have tried to install this configuration:
Centos 6 + libpri 1.4.12 + dahdi 2.5.0.1+2.5.0.1 + attached patch + asterisk 1.8
with no success :(

After installation, i did:
service dahdi stop
modprobe dahdi
modprobe zaphfc

And then,
dahdi_genconf
dahdi_cfg -vvvvvvvvvvvv
which gives me: "0 channels to configure"

Any ideas?

i] Last edited by webon at 2011-10-19 23:09 [/i
11 years 5 months ago #7438 by tim.june
I am working on it!

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Skype: tim.jjune
11 years 4 months ago #7448 by reinerotto
I also started to install a B100P, but on SuSE 11.4
Using the files mentioned in
http://wiki.openvox.cn/index.php/OpenVox_B100P_User_Manual_for_dahdi
did not work for me, some errors occured during compile.

So I used
libpri-1.4.12 and libpri-devel-1.4.12 from SuSEs package installation
dahdi-linux-complete-2.5.0.2+2.5.0.2 from source (asterisk.org)
asterisk-1.8.7.1 from source (asterisk.org)
and applied the new patch version "2.4.0 or above.zip"
At least, this allowed me to successfully generate asterisk and dahdi.
# dahdi_cfg -vvvvvvvvvvvv
DAHDI Tools Version - 2.5.0.2

DAHDI Version: 2.5.0.2
Echo Canceller(s): HWEC, MG2
Configuration
======================

SPAN 1: CCS/ AMI Build-out: 0 db (CSU)/0-133 feet (DSX-1)

Channel map:

Channel 01: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 01)
Channel 02: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 02)
Channel 03: Hardware assisted D-channel (Default) (Echo Canceler: none) (Slaves: 03)

3 channels to configure.

Setting echocan for channel 1 to mg2
Setting echocan for channel 2 to mg2
Setting echocan for channel 3 to none


#lspci | grep ISDN
0b:05.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02)

#dahdi_hardware
pci:0000:0b:05.0 zaphfc+ 1397:2bd0 HFC-S ISDN BRI card

I still have to complete and test the setup, but may be, this gives some more insight into the problem with Cent OS.
11 years 4 months ago #7449 by tim.june
The messages shown above means the driver is working, so what is your problem?

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.
Skype: tim.jjune
11 years 4 months ago #7458 by reinerotto
My installation on SuSE 11.4 does not work:
*CLI> dahdi show channels
*CLI> dahdi show channels
Chan Extension Context Language MOH Interpret Blocked State

May be, my configuration files for dahdi/asterisk are not correct. Does anybody have a working test-config, using B100P only ?

I also tried the description from http://bbs.openvox.cn/viewthread.php?tid=1607& ;extra=page%3D1
which is specifically for SuSE, but 11.3, without success.
Time to create page: 0.040 seconds
Powered by Kunena Forum