B800P NT problem

Hello

I have B800P card and set on this card first port to NT on jumper setting.
I was install dahdi 2.3.0 and asterisk 1.6.2.7.

When i load module:
modprobe wcb4xxp

and I scan my card like:
dahdi_scan
that all of spans is seen as TE. is like:

# dahdi_scan
[1]
active=yes
alarms=RED
description=B4XXP (PCI) Card 0 Span 1
name=B4/0/1
manufacturer=Digium
devicetype=OpenVox B800P
location=PCI Bus 00 Slot 07
basechan=1
totchans=3
irq=18
type=digital-TE
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI,HDB3
framing_opts=ESF,D4,CCS,CRC4
coding=
framing=
[2]
active=yes
alarms=RED
description=B4XXP (PCI) Card 0 Span 2
name=B4/0/2
manufacturer=Digium
devicetype=OpenVox B800P
location=PCI Bus 00 Slot 07
basechan=4
totchans=3
irq=18
type=digital-TE
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI,HDB3
framing_opts=ESF,D4,CCS,CRC4
coding=
framing=
[3]
active=yes
alarms=RED
description=B4XXP (PCI) Card 0 Span 3
name=B4/0/3
manufacturer=Digium
devicetype=OpenVox B800P
location=PCI Bus 00 Slot 07
basechan=7
totchans=3
irq=18
type=digital-TE
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI,HDB3
framing_opts=ESF,D4,CCS,CRC4
coding=
framing=
[4]
active=yes
alarms=RED
description=B4XXP (PCI) Card 0 Span 4
name=B4/0/4
manufacturer=Digium
devicetype=OpenVox B800P
location=PCI Bus 00 Slot 07
basechan=10
totchans=3
irq=18
type=digital-TE
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI,HDB3
framing_opts=ESF,D4,CCS,CRC4
coding=
framing=
[5]
active=yes
alarms=RED
description=B4XXP (PCI) Card 0 Span 5
name=B4/0/5
manufacturer=Digium
devicetype=OpenVox B800P
location=PCI Bus 00 Slot 07
basechan=13
totchans=3
irq=18
type=digital-TE
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI,HDB3
framing_opts=ESF,D4,CCS,CRC4
coding=
framing=
[6]
active=yes
alarms=RED
description=B4XXP (PCI) Card 0 Span 6
name=B4/0/6
manufacturer=Digium
devicetype=OpenVox B800P
location=PCI Bus 00 Slot 07
basechan=16
totchans=3
irq=18
type=digital-TE
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI,HDB3
framing_opts=ESF,D4,CCS,CRC4
coding=
framing=
[7]
active=yes
alarms=RED
description=B4XXP (PCI) Card 0 Span 7
name=B4/0/7
manufacturer=Digium
devicetype=OpenVox B800P
location=PCI Bus 00 Slot 07
basechan=19
totchans=3
irq=18
type=digital-TE
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI,HDB3
framing_opts=ESF,D4,CCS,CRC4
coding=
framing=
[8]
active=yes
alarms=RED
description=B4XXP (PCI) Card 0 Span 8
name=B4/0/8
manufacturer=Digium
devicetype=OpenVox B800P
location=PCI Bus 00 Slot 07
basechan=22
totchans=3
irq=18
type=digital-TE
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=B8ZS,AMI,HDB3
framing_opts=ESF,D4,CCS,CRC4
coding=
framing=



How change span 1 to NT or any else ???

my sys is Slackware 13.0 wit kernel 2.6.29.6

cat /proc/interrupts

18: 643563 IO-APIC-fasteoi b4xxp


Please HELP

ALso is the same situation like http://www.mail-archive.com/[email protected]/msg239890.html

hello,I am afraid that NT mode with wcb4xxp might not be works greatly, it needs to patch! But mISDN works well with our card.

i] Last edited by Joe.Yung at 2010-5-14 10:14 [/i

Ok I was try mISDN v2 with lcr and :
I was
1.Set 1 (in lcr 0) channel to NT (of course I have set jumers on this channel to NT).
2.Set else channel to TE.
3,Connected cabel ISDN from first channel to any esle.
4.Start /etc/rc.mISDN start
5.lcr start
and I have some thing like this in lcradmin state:

─
Ext(port 0: hfc-8s.1-1) NT ptmp use:0 L1 unkn
Int(port 1: hfc-8s.1-2) TE ptmp use:0 L2 unkn L1 unkn
Int(port 2: hfc-8s.1-3) TE ptmp use:0 L2 unkn L1 unkn
Int(port 3: hfc-8s.1-4) TE ptmp use:0 L2 unkn L1 unkn
Int(port 4: hfc-8s.1-5) TE ptmp use:0 L2 unkn L1 unkn
Int(port 5: hfc-8s.1-6) TE ptmp use:0 L2 unkn L1 unkn
Int(port 6: hfc-8s.1-7) TE ptmp use:0 L2 unkn L1 unkn
Int(port 7: hfc-8s.1- TE ptmp use:0 L2 unkn L1 unkn

and any leds no up to green

My cable is 3456 to 3456. no connected from first to second channel i the same card (NT-TE).

How do it to work ???? because now seems like not working



Please Help

hello:
have you read the wiki for mISDN v2? please read that before doing, the URL:
http://wiki.openvox.cn/index.php/OpenVox_B400P_User_Manual_for_mISDN_V2

Yes I was read this many times. but when I try install wtih straight instruction then when I will try compile mISDN then:


/usr/src/mISDN# make
make all-recursive
make[1]: Entering directory `/usr/src/mISDN'
Making all in standalone
make[2]: Entering directory `/usr/src/mISDN/standalone'
make[2]: *** No rule to make target `all'. Stop.
make[2]: Leaving directory `/usr/src/mISDN/standalone'
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory `/usr/src/mISDN'
make: *** [all] Error 2



I can only comipile like:
make modules
make modules-install
./std2kern

but only when I not change hfcmulti.c
If I will changed that file I have another error like:


/usr/src/mISDN/standalone/drivers/isdn/hardware/mISDN/hfcmulti.c: In function 'hfcmulti_init':
/usr/src/mISDN/standalone/drivers/isdn/hardware/mISDN/hfcmulti.c:5207: error: 'struct hfc_multi' has no member named 'dslot'
/usr/src/mISDN/standalone/drivers/isdn/hardware/mISDN/hfcmulti.c:5212: error: 'struct hfc_multi' has no member named 'dslot'
/usr/src/mISDN/standalone/drivers/isdn/hardware/mISDN/hfcmulti.c:5216: error: 'struct hfc_multi' has no member named 'dslot'
make[4]: *** [/usr/src/mISDN/standalone/drivers/isdn/hardware/mISDN/hfcmulti.o] Error 1
make[3]: *** [_module_/usr/src/mISDN/standalone/drivers/isdn/hardware/mISDN] Error 2
make[3]: Leaving directory `/usr/src/linux-2.6.29.6'
make[2]: *** [modules_] Error 2
make[2]: Leaving directory `/usr/src/mISDN/standalone'
make[1]: *** [modules] Error 2
make[1]: Leaving directory `/usr/src/mISDN/standalone

i] Last edited by grzegorz at 2010-5-14 18:32 [/i