D130 Not being detected by Dahdi

Hi,

I have recently purchased a D130 card and installed it on my workstation. after installing dahdi it is not being recognized by dahdi. Even it is being recognized by linux as communication controller... below are the details

System: HP Z200 Workstation
OS: Centos 5.9 (Final)

libpri-1.4.14
dahdi-linux-complete-2.6.2+2.6.2
asterisk-1.8.19.1

[root@localhost src]#uname -r
2.6.18-348.3.1.el5xen

[root@localhost src]#uname -a
Linux localhost.localdomain 2.6.18-348.3.1.el5xen #1 SMP Mon Mar 11 20:28:48 EDT 2013 x86_64 x86_64 x86_64 GNU/Linux

[root@localhost src]#lspci
25:00.0 Network controller: OpenVox Communication Co. Ltd. D130P/D130E Single-port E1/T1 card (3rd GEN) (rev 15)
Subsystem: Device 0005:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 32000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 3
Region 0: Memory at f0500000 (32-bit, non-prefetchable) [size=32K]

after issueing "make install" when installing dahid it shows a message that hardware was not found...

DAHDI has been configured.

List of detected DAHDI devices:

No hardware found
make[1]: Leaving directory `/usr/src/dahdi-linux-complete-2.6.2+2.6.2/tools'

I followed the D130 insallation guide from

wiki.openvox.cn/index.php/OpenVox_D130P_Dahdi_en

Please help as I have to make this system live with telco.

Thanks and Regards,

Nasir

hi,

Does it can generate the config normally? pls stop asterisk and run the the following command in turns to try
service dahdi stop
modprobe dahdi
modprobe opvxd115
dahdi_genconf
if still have problem, you can contact me via msn or skype

msn: This email address is being protected from spambots. You need JavaScript enabled to view it.
skype: chunlei.yi

Dear chunlei.yi,

Thank you for quick reply. I already tried these steps but it did not work. Below is the detail:

[root@localhost ~]# service dahdi stop
Unloading DAHDI hardware modules: done
[root@localhost ~]# modprobe dahdi
[root@localhost ~]# modprobe opvxd115
FATAL: Module opvxd115 not found.
[root@localhost ~]# dahdi_genconf
Empty configuration -- no spans
Empty configuration -- no spans
[root@localhost ~]#

I am now also going to add you on skype. please accept.

The issue has been solved. Thanks for your great support.

Cheers,

Nasir

OS: Linux 2.6.32-358.11.1.el6.x86_64 #1 SMP Wed Jun 12 03:34:52 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux
lspci -vvvv
02:00.0 Network controller: OpenVox Communication Co. Ltd. D130P/D130E Single-port E1/T1 card (3rd GEN) (rev 15)
Subsystem: Device 0005:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 32000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11


Downloaded and installed all packages per instructions
....
cd dahdi-linux-complete-2.7.0+2.7.0/
make
make install
make config
List of detected DAHDI devices:
No Hardware found

Please help....thank you

OS: Linux 2.6.32-358.11.1.el6.x86_64 #1 SMP Wed Jun 12 03:34:52 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux
lspci -vvvv
02:00.0 Network controller: OpenVox Communication Co. Ltd. D130P/D130E Single-port E1/T1 card (3rd GEN) (rev 15)
Subsystem: Device 0005:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 32000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c1b00000 (32-bit, non-prefetchable) [size=32K]


Downloaded and installed all packages per instructions
....
cd dahdi-linux-complete-2.7.0+2.7.0/
make
make install
(all ok)
make config
List of detected DAHDI devices:
No Hardware found

Sorry I posted this on another thread...and have repeated in this new thread.
Please help....thank you