keywords: ip pbx voip gateway gsm gateway

×

Notice

The forum is in read only mode.
× Technical information on install and config asterisk, zaptel under different OSs

Problem with installing DE115P and G400P together

12 years 6 months ago #7379 by afce05
System info:
Hardware : DE115P - 1 piece, G400P - 2 pieses
Software: TrixBox 2.8 with Asterisk 1.6 (CentOS 5.5) dahdi 2.3.0

The system was working normally: receiving calls from E1 channels, transfer via GSM sim cards.
But after adding one more sim card, E1 channel stops receiving calls
Here is some check results:

gmesg:
dahdi_echocan_mg2: Registered echo canceler 'MG2'
dahdi: Registered tone zone 0 (United States / North America)
opvxd115 0000:05:05.0: opvxd115: Span 1 configured for CCS/HDB3/CRC4
opvxd115 0000:05:05.0: SPAN 1: Primary Sync Source
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: RCLK source set to span 1
opvxd115 0000:05:05.0: Recovered timing mode, RCLK set to span 1
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000001, CIS = 0081
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000001, CIS = 0081
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000001, CIS = 0081
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000001, CIS = 0081
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
opvxd115 0000:05:05.0: 2G: Got interrupt, status = 00000002, CIS = 0080
opvxd115 0000:05:05.0: Reg 5 is fbdff014
VPM450: echo cancellation for 32 channels
opvxd115 0000:05:05.0: NMF workaround on!
opvxd115 0000:05:05.0: VPM450: hardware DTMF disabled.
opvxd115 0000:05:05.0: VPM450: Present and operational servicing 1 span(s)


extensions.conf:
exten => s,1,Answer() // answer the inbound call
exten => s,n,Wait(3)
exten => s,n,Dial(SIP/101)
exten => s,n,Dial(SIP/102)
exten => s,n,Dial(SIP/103)
exten => s,n,Dial(extra/g15/0503132823)
exten => s,n,Dial(extra/g15/0503492912)
:exten => s,n,Playback()
exten => s,n,Playback(vm-nobodyavail)
exten => s,n,Playback(please-try-again-later)
exten => s,n,Hangup()
12 years 6 months ago #7380 by hua
Hi,
please give us more details and add me MSN This email address is being protected from spambots. You need JavaScript enabled to view it. or provide SSH to [font=华文中宋]This email address is being protected from spambots. You need JavaScript enabled to view it. . [/size][/font]
we will check your system as soon as possible .Thanks!

Best regards!
upper.hua
12 years 4 months ago #7528 by afce05
cards conflict (sharing irq port) Hi again!

There is a problem:

DE115P and G400P is sharing IRQ 225 port, so dahdi changing master from DE115P to G400P and back.

Here is cat proc/interrapts output:

CPU0 CPU1
0: 860167 863342 IO-APIC-edge timer
1: 8 9 IO-APIC-edge i8042
7: 0 0 IO-APIC-edge parport0
8: 1 2 IO-APIC-edge rtc
9: 0 0 IO-APIC-level acpi
50: 834639 834398 IO-APIC-level opvxg4xx
66: 245 0 PCI-MSI HDA Intel
169: 850946 846360 IO-APIC-level ahci, opvxa24xx
225: 1661546 1661663 IO-APIC-level ata_piix, ata_piix, opvxd115, opvxg4xx
233: 2996 0 PCI-MSI eth0
NMI: 0 0
LOC: 1724916 1722057
ERR: 0
MIS: 0

On our server there are 4 PCI slots and all are busy this openvox cards

PCI #1 - G400P
PCI #2 - G400P
PCI #3 - AE1610P
PIC #4 - DE115P

What we could do to avoid this problem?
Time to create page: 0.036 seconds
Powered by Kunena Forum